KindPack ShapePaw Die-Cut Pouch
KindPack ShapePaw Die-Cut Pouch
Custom die-cut pouch with a shaped silhouette that stands out on impulse pegs and gift displays. Rebuilt into the KP-ECO-007 Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers green parameter family: thin-gauge mono-PE portion and roll-stock direction. Blank front panel, no brand on the pack. All specifications are Draft / Indicative / To Confirm - not a quote.
Specification
| Bag type | Green & Recyclable |
| Structure | Three-side-seal or stand-up pouch with a custom die-cut outer silhouette and a straight, unshaped top edge for closure hardware Re-homed to the KP-ECO-007 Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers build direction: Three-side-seal flat pouch cut from roll stock, with a longitudinal fin seal and two end seals; optional rounded corner and a tear-line notch for tearing by hand without scissors (Draft / To Confirm). |
| Material | DRAFT / TO CONFIRM - KP-ECO-007 family material direction: DRAFT / TO CONFIRM - mono-material PE direction to keep a small-format pack in one stream. Sample candidates: (a) MDO-PE 20 micron / water-based ink / PE sealant 55-70 micron; (b) PE with a 30% PCR direction in the outer layer; (c) a lighter PE/PE structure where a higher barrier is required for gravy fills. Grade, PCR share and barrier level are unverified - not a confirmed specification. SKU-specific options carried over from the original catalogue and still to be confirmed: Direction to select at sampling: PET/PE composite cut to a custom die; die geometry must be checked against fill-line clearance and seal width before tooling is committed. |
| Total thickness | 100-130 micron total (Draft / To Confirm) - family reference for KP-ECO-007: 75-90 microns total (Draft / To Confirm) - Draft / To Confirm |
| Closure | Press-to-close strip on the straight top edge with a shaped tear notch |
| Print process | Flexographic surface print, up to 8 stations, water-based inks at high line speed; register to be set for the narrow web width (Draft / To Confirm) Applied to this SKU's Shaped Custom-Die-Cut Pouch format. |
| Finish | Gloss or matte finish depending on the print line; no foil, no metallic ink and no cold-seal coating that would add a second material Original catalogue surface direction to confirm: Matte with gloss edge highlights that follow the die line |
| Window | None. The pack is fully printed or left as a solid unprinted area; a clear window on a portion pack adds a material and is not offered Format note for KP-PF-022: Window, handle and valve or spout options are not part of this SKU build unless listed; any addition must be re-verified inside the family material direction. |
| Handle | None. Not applicable to this format Format note for KP-PF-022: Window, handle and valve or spout options are not part of this SKU build unless listed; any addition must be re-verified inside the family material direction. |
| Degassing valve | None. No valve and no spout; this is a tear-open portion pack Format note for KP-PF-022: Window, handle and valve or spout options are not part of this SKU build unless listed; any addition must be re-verified inside the family material direction. |
| Origin | Dongguan, Guangdong, China |
Sizes & fill weight
| Available sizes | 2 oz / 4 oz / 6 oz (57 g / 113 g / 170 g) - Draft / To Confirm against fill weight and bulk density |
| Dimensions (W x H + gusset) | 2 oz / 4 oz / 6 oz (57 g / 113 g / 170 g). Draft die-cut silhouette envelope W x H (mm): 2 oz approx. 120 x 200; 4 oz approx. 140 x 230; 6 oz approx. 160 x 255, with a straight unshaped top edge. Draft / To Confirm against fill-line clearance and minimum seal width. |
| Monthly capacity | 500,000-1,200,000 pcs / month |
Bags are built to your fill weight and bulk density, not to a catalogue number — send us the product and we confirm the structure before tooling.
MOQ & unit pricing
500 pcs (digital print) / 20,000 pcs (gravure)
| 500 pcs | USD 0.198 / pc |
| 1,000 pcs | USD 0.178 / pc |
| 5,000 pcs | USD 0.099 / pc |
| 20,000 pcs | USD 0.074 / pc |
Prices are FOB Dongguan and exclude duties and taxes.
Lead time & payment
| Production lead time | 30-45 days |
| Sample lead time | 15-20 days |
| Payment terms | T/T - 40% deposit, balance before shipment |
Documentation supplied
| Food-contact documentation | Food-contact compliance letter for the PE film and any reseal strip option - TO REQUEST | Declaration of Compliance covering film, reseal strip (if used) and printing ink - TO PREPARE | Migration test report on the finished laminate - TO REQUEST | Seal strength and burst test report at the 40 g fill weight and at line speed - TO PREPARE | Tear-notch function test and opening-force report - TO PREPARE | PCR feedstock and food-contact suitability documentation if recycled content is used - TO REQUEST | Converting plant GMP certificate (BRCGS, SQF or equivalent) - TO REQUEST | Portion-weight accuracy and seal-contamination tolerance data for dry and moist fills - TO PREPARE | Food-contact declaration for this SKU's closure and fitment components (Press-to-close strip on the straight top edge with a shaped tear notch) - TO REQUEST from the component supplier |
| Environmental claim status | CLAIM PENDING - NOT VERIFIED. No recyclability, recycled-content or mono-material claim is validated for this SKU. Small-format films are frequently below the size threshold used by recovery programmes, and this must be checked rather than assumed. Any PCR figure, any store drop-off wording and any material-reduction claim require supplier declarations and a programme eligibility check first. Permitted wording today: 'mono-material PE direction, small-format recovery eligibility under verification'. SKU note for KP-PF-022: the claim-critical components are the closure and fitment actually used on this build (Press-to-close strip on the straight top edge with a shaped tear notch) and the end-of-life route of the pack format of this SKU; both must be covered by the assessments listed before any wording changes. |
About this structure
ShapePaw trades the standard rectangle for a shaped outline. The die-cut silhouette carries through the whole pack, so a brand can become recognizable by profile alone on a crowded pegboard, and the shape naturally supports seasonal and gift-set merchandising. The top edge stays straight so zipper or reseal hardware still functions normally, and a shaped tear notch aligns with the die line. Playful paw and confetti patterns in candy-bright colors target gift, holiday and new-pet occasions. In the rebuilt 36-SKU green matrix this product is re-homed to parameter family KP-ECO-007 - Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers - on the basis of structure-first match: three-side-seal / stand-up base with a straight top edge, the same portion-pouch build; the die-cut silhouette is a tooling variant. The family design direction is: Cut film gauge to the minimum that still seals at line speed; keep the pouch mono-material PE; avoid a separate clear window or a paper layer on a small format; use water-based inks; and investigate whether the finished portion size can stay above any minimum size threshold used for film collection, rather than assuming eligibility. The front panel stays blank and carries no brand of ours, so the buyer's own label can be applied. Nothing here is a verified environmental statement: CLAIM PENDING - NOT VERIFIED. No recyclability, recycled-content or mono-material claim is validated for this SKU. Small-format films are frequently below the size threshold used by recovery programmes, and this must be checked rather than assumed. Any PCR figure, any store drop-off wording and any material-reduction claim require supplier declarations and a programme eligibility check first. Permitted wording today: 'mono-material PE direction, small-format recovery eligibility under verification'. Duties & taxes are not included in quoted prices.
Why brands choose it
- One Bite - high-speed small format, crisp studio cutouts - applied to the Shaped Custom-Die-Cut Pouch format
- Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers
Frequently asked
Is your company a manufacturer or a trading company?
We are a direct manufacturer with our own factory in Dongguan, Guangdong, China, founded in 2014. You are welcome to arrange a virtual or on-site factory tour.
Can your packaging be customized?
Yes. We provide full OEM/ODM services including custom printing, size, material structure, pouch type, zipper / spout / handle options, and artwork support.
What types of packaging bags can you produce?
We produce stand-up pouches, flat bottom bags, spout pouches, retort pouches, side gusset bags, quad seal bags, kraft paper bags, mono-material recyclable bags, window bags, and bulk bags.
How do I request a quotation?
Please share your bag type, target size, estimated order quantity, material preference, and design artwork (AI or PDF). Our sales team will reply with a detailed quotation and sampling plan.
How can I contact you?
Use the inquiry form on this page, email us, or reach us via WhatsApp / WeChat. A dedicated project manager will follow up within one business day.
Need this quoted?
Send your fill weight, first-run quantity and target market to kindpackpouch@gmail.com or WhatsApp +86 150 1487 8185. You will get a transparent quote, the MOQ for your structure, and a sample lead time within one business day. Duties and taxes are not included in quoted prices.