KindPack RollForm Print Film
KindPack RollForm Print Film
Printed rollstock for automated VFFS lines, supplied with a registered repeat for accurate cut-off and low film waste. Rebuilt into the KP-ECO-007 Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers green parameter family: thin-gauge mono-PE portion and roll-stock direction. Blank front panel, no brand on the pack. All specifications are Draft / Indicative / To Confirm - not a quote.
Specification
| Bag type | Green & Recyclable |
| Structure | Printed rollstock supplied on cores with an unprinted sealant side and a registered graphics repeat for accurate cut-off Re-homed to the KP-ECO-007 Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers build direction: Three-side-seal flat pouch cut from roll stock, with a longitudinal fin seal and two end seals; optional rounded corner and a tear-line notch for tearing by hand without scissors (Draft / To Confirm). |
| Material | DRAFT / TO CONFIRM - KP-ECO-007 family material direction: DRAFT / TO CONFIRM - mono-material PE direction to keep a small-format pack in one stream. Sample candidates: (a) MDO-PE 20 micron / water-based ink / PE sealant 55-70 micron; (b) PE with a 30% PCR direction in the outer layer; (c) a lighter PE/PE structure where a higher barrier is required for gravy fills. Grade, PCR share and barrier level are unverified - not a confirmed specification. SKU-specific options carried over from the original catalogue and still to be confirmed: Direction to select at sampling: PET/PE or BOPP/PE laminate for general dry goods; metallized or EVOH high-barrier direction for fat-rich formulas. Machine compatibility must be validated on the buyer's filler before approval. |
| Total thickness | 70-110 micron total (Draft / To Confirm by machine and barrier requirement) - family reference for KP-ECO-007: 75-90 microns total (Draft / To Confirm) - Draft / To Confirm |
| Closure | Closure is created by the customer's form-fill-seal machine; film is supplied with a registered print repeat to align optional zipper application |
| Print process | Flexographic surface print, up to 8 stations, water-based inks at high line speed; register to be set for the narrow web width (Draft / To Confirm) Applied to this SKU's Rollstock Film for Form-Fill-Seal Lines format. |
| Finish | Gloss or matte finish depending on the print line; no foil, no metallic ink and no cold-seal coating that would add a second material Original catalogue surface direction to confirm: Matte or gloss surface with reverse-printed graphics protected inside the laminate |
| Window | None. The pack is fully printed or left as a solid unprinted area; a clear window on a portion pack adds a material and is not offered Format note for KP-PF-008: Supplied as printed rollstock, so window, handle and valve features exist only if the buyer form-fill-seal line adds them. |
| Handle | None. Not applicable to this format Format note for KP-PF-008: Supplied as printed rollstock, so window, handle and valve features exist only if the buyer form-fill-seal line adds them. |
| Degassing valve | None. No valve and no spout; this is a tear-open portion pack Format note for KP-PF-008: Supplied as printed rollstock, so window, handle and valve features exist only if the buyer form-fill-seal line adds them. |
| Origin | Dongguan, Guangdong, China |
Sizes & fill weight
| Available sizes | Roll format custom to bag size; typical finished packs 0.5 lb - 10 lb (227 g - 4.5 kg) - Draft / To Confirm against fill weight and bulk density |
| Dimensions (W x H + gusset) | Roll format, custom to bag size; typical finished packs 0.5 lb - 10 lb (227 g - 4.5 kg). Draft roll parameters: web width 200-900 mm, core diameter 76 mm or 152 mm, print repeat step 200-600 mm, eye-mark pitch aligned to the buyer cut length. Draft / To Confirm against the buyer form-fill-seal machine. |
| Monthly capacity | 40,000-90,000 kg / month |
Bags are built to your fill weight and bulk density, not to a catalogue number — send us the product and we confirm the structure before tooling.
MOQ & unit pricing
500 pcs (digital print) / 20,000 pcs (gravure)
| 500 pcs | USD 1.415 / pc |
| 1,000 pcs | USD 1.274 / pc |
| 5,000 pcs | USD 0.708 / pc |
| 20,000 pcs | USD 0.531 / pc |
Prices are FOB Dongguan and exclude duties and taxes.
Lead time & payment
| Production lead time | 20-32 days |
| Sample lead time | 7-12 days |
| Payment terms | T/T - 40% deposit, balance before shipment |
Documentation supplied
| Food-contact documentation | Food-contact compliance letter for the PE film and any reseal strip option - TO REQUEST | Declaration of Compliance covering film, reseal strip (if used) and printing ink - TO PREPARE | Migration test report on the finished laminate - TO REQUEST | Seal strength and burst test report at the 40 g fill weight and at line speed - TO PREPARE | Tear-notch function test and opening-force report - TO PREPARE | PCR feedstock and food-contact suitability documentation if recycled content is used - TO REQUEST | Converting plant GMP certificate (BRCGS, SQF or equivalent) - TO REQUEST | Portion-weight accuracy and seal-contamination tolerance data for dry and moist fills - TO PREPARE | Food-contact declaration for this SKU's closure and fitment components (Closure is created by the customer's form-fill-seal machine; film is supplied with a regis) - TO REQUEST from the component supplier |
| Environmental claim status | CLAIM PENDING - NOT VERIFIED. No recyclability, recycled-content or mono-material claim is validated for this SKU. Small-format films are frequently below the size threshold used by recovery programmes, and this must be checked rather than assumed. Any PCR figure, any store drop-off wording and any material-reduction claim require supplier declarations and a programme eligibility check first. Permitted wording today: 'mono-material PE direction, small-format recovery eligibility under verification'. SKU note for KP-PF-008: the claim-critical components are the closure and fitment actually used on this build (Closure is created by the customer's form-fill-seal machine; film is supplied with a registered print repeat t) and the end-of-life route of the pack format of this SKU; both must be covered by the assessments listed before any wording changes. |
About this structure
RollForm is the film-first option for brands that bag on their own equipment. Graphics are reverse-printed and protected inside the laminate so scuffing on the machine cannot dull the artwork, and print repeat is registered to the buyer's cut length to minimize wasted film at start-up and changeover. The blueprint-technical graphic language is designed to communicate precision and diligence, which suits performance and veterinary-channel brands. Film width, core size and wind orientation are specified per machine. In the rebuilt 36-SKU green matrix this product is re-homed to parameter family KP-ECO-007 - Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers - on the basis of structure-first match: roll-stock film fed to a form-fill-seal line, the same supply form as the portion-pouch family. The family design direction is: Cut film gauge to the minimum that still seals at line speed; keep the pouch mono-material PE; avoid a separate clear window or a paper layer on a small format; use water-based inks; and investigate whether the finished portion size can stay above any minimum size threshold used for film collection, rather than assuming eligibility. The front panel stays blank and carries no brand of ours, so the buyer's own label can be applied. Nothing here is a verified environmental statement: CLAIM PENDING - NOT VERIFIED. No recyclability, recycled-content or mono-material claim is validated for this SKU. Small-format films are frequently below the size threshold used by recovery programmes, and this must be checked rather than assumed. Any PCR figure, any store drop-off wording and any material-reduction claim require supplier declarations and a programme eligibility check first. Permitted wording today: 'mono-material PE direction, small-format recovery eligibility under verification'. Duties & taxes are not included in quoted prices.
Why brands choose it
- One Bite - high-speed small format, crisp studio cutouts - applied to the Rollstock Film for Form-Fill-Seal Lines format
- Single-Serve Mono-PE Portion Pouch for Training Treats and Toppers
Frequently asked
Is your company a manufacturer or a trading company?
We are a direct manufacturer with our own factory in Dongguan, Guangdong, China, founded in 2014. You are welcome to arrange a virtual or on-site factory tour.
Can your packaging be customized?
Yes. We provide full OEM/ODM services including custom printing, size, material structure, pouch type, zipper / spout / handle options, and artwork support.
What types of packaging bags can you produce?
We produce stand-up pouches, flat bottom bags, spout pouches, retort pouches, side gusset bags, quad seal bags, kraft paper bags, mono-material recyclable bags, window bags, and bulk bags.
How do I request a quotation?
Please share your bag type, target size, estimated order quantity, material preference, and design artwork (AI or PDF). Our sales team will reply with a detailed quotation and sampling plan.
How can I contact you?
Use the inquiry form on this page, email us, or reach us via WhatsApp / WeChat. A dedicated project manager will follow up within one business day.
Need this quoted?
Send your fill weight, first-run quantity and target market to kindpackpouch@gmail.com or WhatsApp +86 150 1487 8185. You will get a transparent quote, the MOQ for your structure, and a sample lead time within one business day. Duties and taxes are not included in quoted prices.